Scott L. Carlson
  • Male
  • Cloverdale, CA
  • United States
Share on Facebook Share

Scott L. Carlson's Discussions

Tatum 17 for whitewater
6 Replies

    Hi All,   My Tatum 17 rebuild is almost finished.   If I wanted to use it on some class 3 runs, should I deck it out and add compartments? Should i keep the original open layout and stay on the…Continue

Started this discussion. Last reply by Scott L. Carlson May 19.

Tatum 17 finish
8 Replies

Hi All,My first post, hope i am in the right spot.I have removed the bottom, replaced some ribs and am ready to replace some of the 1/4 inch side damage. My question for opinion. Can I epoxy over…Continue

Started this discussion. Last reply by Scott L. Carlson Feb 22.

 

Scott L. Carlson's Page

Latest Activity

Scott L. Carlson replied to Donnie Clinton's discussion Books / DVDs'???????
"Will get some photos together. I am going for the worst "before" picture. Scott"
May 30
Scott L. Carlson replied to Donnie Clinton's discussion Books / DVDs'???????
"Hi Rick, There were a few grub looking things, should have saved them. When I was dealing with all of the rot, I fortunately found Greg Tatman. He was working on a boat damaged in a long rapid while the boat was submerged. He showed how to make…"
May 29
Scott L. Carlson replied to Donnie Clinton's discussion Books / DVDs'???????
"   Donnie,    I will figure out how to post before and after photos. Just do not expect my photos to be like the awesome Jayson Hayes shots in this thread. Maybe I can use photoshop. Or maybe all of the beautiful boats were…"
May 20
Scott L. Carlson replied to Donnie Clinton's discussion Books / DVDs'???????
"Hi Donnie, David has been giving me some answers amout finishing my Tatman 17. Good info. My boat bottom and six inches up the sides was compost. Complete with mushrooms, insects, etc. I can share from a novice viewpoint. Just shout.    …"
May 19
Scott L. Carlson replied to Scott L. Carlson's discussion Tatum 17 for whitewater
"Perfect, I will keep in touch with my progress. Thanks"
May 19
Scott L. Carlson replied to Scott L. Carlson's discussion Tatum 17 finish
"Sounds good, thanks for the ideas."
Feb 22
Shawn Baker replied to Scott L. Carlson's discussion Tatum 17 finish
"Yes, to prevent epoxy sags, do it on a horizontal surface. If you have to di it vertically, do several thin coats...or let it sag, use a cabinet scraper to get the big boogs, fair with a longboard, and do a thin final fill coat with a squeegee to…"
Feb 19
Scott L. Carlson replied to Scott L. Carlson's discussion Tatum 17 finish
"Thanks Shawn +Jayson, I do not want to do something that reduces my options. If one coat of epoxy does not seem adequate. I can add another for the checking. Skip the wood flour.    To avoid epoxy running down the sides, do you tip the…"
Feb 19
Shawn Baker replied to Scott L. Carlson's discussion Tatum 17 finish
"Blush is a nasty pain in the butt.One doesn't have to use non-blushing epoxy.  It comes off quite easily with warm soapy water...wipe the majority off while it's still hot/wet and it will come off on the rag.  A final hot water…"
Feb 14
Shawn Baker replied to Scott L. Carlson's discussion Tatum 17 finish
"I don't like that plywood checks.  I am glassing EVERY surface in my dory except for my gunnels.  I think epoxy + wood dust is just a bandaid.  I'd recommend using thinned epoxy to really saturate, or use small quantities of…"
Feb 14
Jayson Hayes replied to Scott L. Carlson's discussion Tatum 17 finish
"Scott, make sure you use a non blushing epoxy or you will be on the hook for a lot of extra work when it comes to prepping for paint and varnish. System 3 silver tip is great for this, west system is not unless you use the 207 and even that can be…"
Feb 13
Scott L. Carlson replied to Scott L. Carlson's discussion Tatum 17 finish
"    Thanks Shawn   I  need to fill some checking plywood and will do that with epoxy+wood dust.   I might as well add another layer of epoxy after the first thickened exterior batch. I planned to epoxy the floor before…"
Feb 12
Shawn Baker replied to Scott L. Carlson's discussion Tatum 17 finish
"If you're doing a varnish finish, be neat with the epoxy.  Varnish looks different over epoxy than over bare wood...so either mask off the scarfs when you epoxy them and keep the outside of the wood all dry and ready for varnish...or sand…"
Feb 12

Profile Information

Hometown:
Cloverdale
About Me:
Restoring a Greg Tatman 17 footer. Nearly a yard art candidate.Woodworking skills are fair, boat building/rebuilding is new.
Boats I own:
Tatman Mackenzie River Drift Boat

Comment Wall

You need to be a member of Wooden Boat People to add comments!

Join Wooden Boat People

  • No comments yet!
 
 
 

© 2019   Created by Randy Dersham.   Powered by

Badges  |  Report an Issue  |  Terms of Service