Guy's Wooden Drift Boat Project

Hello Everyone,

 

My name is Guy and this is my first post in this forum.  I am here because I want to build a wooden drift boat and, undoubtedly, I will occasionally need advice of the pool of experts and experienced drift boat builders on this forum.

 

In preparation for this project I have read and studied three books: Drift Boats and River Dories by R. L. Fletcher, Boatbuilding with Plywood by G. L. Witt, and Covering Wooden Boats with Fiberglass by A. H. Vaitses.  I have also developed my own set of construction plans based off of the "Original McKenzie Double-Ender with Transom" in Fletcher's book.  I used and MS Excel spreadsheet to calculate all of the dimensions, cut angles, compound angles, and bevel angles of all frame components and I used Pilot3D software to calculate the as-cut dimensions of the plywood sides and bottom.  At this point I am pretty comfortable with the mechanics of construction and I think that I am just about ready to start purchasing lumber.

 

Presently, I plan to use Meranti Hydro-Tek plywood; 1/4-in. on the sides and 1/2-in. on the bottom.  I found plenty of places to purchase these materials, but they are all far away from Idaho Falls, Idaho, and as a result shipping costs more than the materials.  Are any of you aware of a business within a few hundred miles of Idaho Falls that sells this plywood?  I have a few requests in to the local lumber companies, but I have yet to talk with someone who has heard of this material before.

 

I also plan to use Port Orford Cedar (CVG) for the straight frame sections and White Oak (quater sawn) for the bent frame sections (chine logs and sheer rails).

 

Thank you, Guy

Views: 105432

▶ Reply to This

Replies to This Discussion

Permalink Reply by Guy Fredrickson on July 18, 2020 at 9:47am

I’m also adding wood to the bottom ends of the side frames where they join the bottom frames. 


Permalink Reply by Guy Fredrickson on July 18, 2020 at 5:10pm

I drilled out all the old wood screw holes in the gripe to 1/4-inch and filled with mahogany dowels and waterproof Gorilla glue. I decided to use dowels rather than toothpicks this time because it’s the bow and I want it to be as strong as possible. 

Permalink Reply by Guy Fredrickson on July 19, 2020 at 6:01pm

The gripe is starting to look good with the old holes plugged with dowels. 


Permalink Reply by Guy Fredrickson on July 20, 2020 at 6:50pm

I’m starting to fit the frames back onto the hull. This will take time to fair all the surfaces to the proper contours. 

Permalink Reply by Andrew on July 21, 2020 at 10:57pm

That's really nice, I love to build wood ship kits and its my hobby. Currently I am a learner.

Permalink Reply by Guy Fredrickson on July 23, 2020 at 6:49pm

Hi Andrew. Thanks. Post a picture of one of your models here. I like to see one. Guy

Permalink Reply by Guy Fredrickson on July 29, 2020 at 7:31pm

I’ve got the frames bolted into position. I’m just about ready to dry fit the chines. 

Permalink Reply by Guy Fredrickson on August 3, 2020 at 7:04am

Starting to dry fit the keel and chines. 

Permalink Reply by Rick Newman on August 3, 2020 at 8:36am

You have been busy! Looking good!

Rick N

Permalink Reply by Guy Fredrickson on August 6, 2020 at 8:04pm

Thanks Rick. I’m try to keep it moving forward. 

Permalink Reply by Guy Fredrickson on August 6, 2020 at 8:08pm

I got the frames and the old plywood bottom to fit together pretty well. So I took it all apart again. I’ll do some light sanding, seal coat everything with Smith’s Penetrating Epoxy Sealer, paint everything with Sandusky Bilge Paint, and reassemble it for the final time. 

Permalink Reply by Guy Fredrickson on August 7, 2020 at 8:16am

This is the old plywood bottom. I will use it as a pattern to cut the new plywood. 

RSS

© 2024   Created by Randy Dersham.   Powered by

Badges  |  Report an Issue  |  Terms of Service