I'm selling a nice drift boat for a friend. 17 ft, 1999 wood and fiberglass. All set up for fishing. She spent most of her life up on the Bighorn River. Fresh varnish on the bright work, really nice trailer with new rubber all around. Oars, PFD, anchor, beer coozies....all included! $5800/offer Hal @ 970.531.2326. Owner lives in Denver, but the boat is in Pagosa Springs. Thanks!…Continue
Added by Hal Jaeke on June 8, 2019 at 6:52pm — No Comments
I'm selling a nice boat for a friend. Comes with everything needed to put in and start fishing ( just add rods!) Fresh varnish on the bright work, a really nice trailer with new rubber all around. Call or text Hal for more info. 970.531.2326 The owner lives in Denver, but the boat is presently in Pagosa Springs, Co. 20190404_133721.jpg
Added by Hal Jaeke on June 8, 2019 at 6:51pm — No Comments
I am selling my refurbished Rays river dorie . Located in Basalt Colorado. I hate to let it go ....
$ 4,000.oo Thank's for looking ; photo's on my page. let me know if you cannot view. Mike
Added by Mike Wilcox on May 18, 2019 at 9:18am — No Comments
I've got the skid shoe off and in the garbage. All the ring nails are pulled out or clipped and back filled. I've epoxied/wood powdered all dings and sanded from bow to where the skid shoe ended. I was able to get that far using 80 grit.
My question is, Just how clean/sanded does the bottom have to be before glassing? From where the skid shoe ended to the transom is being a bear to clean up with 80 grit. So was the bow bottom but i got that done...with…Continue
Hello Wooden Boat Peeps, I wanted to let everyone know that I can supply accessories and kits. Accessories include UHMW oar lock blocks, white oak kneelock horns with drink holders, Dierks double bow eyes with 1/4-20 all thread for bolting through bow stem, Dierks anchor systems, and UHMW transom bang plates for anchor swing. Also available are kits, anywhere from alaskan yellow cedar frame kits with AYC bow stem, transom trim, and frame spacing dimensions, to full kits where everything is…Continue
Added by Kurt Selisch on June 10, 2018 at 4:47pm — No Comments
Added by Richard Sutherland on May 24, 2018 at 8:30am — No Comments
Most of you folks here aren't in the market for class, but for those of you that are, I just posted my winter offerings. If you want to build a boat, shape an oar, cast custom bronze boat hardware--but don't have the nerve to start out on your own, this might be just the ticket.…Continue
Added by Brad Dimock on December 11, 2017 at 10:09pm — No Comments
There was a wooden boat on Craigslist and I went to look at it. It was pretty, and the seller said it only leaked a little, that he would not hesitate to take it fishing. That was good enough for me. It looked great on a soggy December afternoon in a dark shed so I bought it. It came with a motor and trailer! I knew I’d sell the motor and that would pay for sand paper and varnish, with cash left over to buy beer to lubricate the sanding and varnishing.
Added by Bob H on June 21, 2017 at 2:44pm — No Comments
I have a 16' Don Hill drift boat kit I never got around building and would like it to go to a good home and someone to complete it. I have had it stored in my garage for over 10 years and moving soon to much smaller place so need to down size my stuff. The Kit includes all the ribs, transom, bow stem, and a box of hardware. I also have the instructions but will need to find them. I can be contacted directly at:
270 East Mayes St.
We should probably be arrested for doing this but we did it:
Selling my Rays River Dory Perfect Mac.
Boat only has 5 years of light use and is in Bristol Condition. I purchased from the original owner who commissioned to have this built and for what ever reason after he applied oils and varnish he never used it. Sat in his attached garage for 17 years. Superb craftsmanship and timeless design.…Continue
Added by Bob burda on June 10, 2016 at 4:07pm — No Comments
The Enki drawings are finally done. You can check them out here: http://shoelessmusings.blogspot.com/2016/05/enki-drawings-done.html
Added by Mark Stuberr on May 31, 2016 at 5:24pm — No Comments
New blog post,
Added by Mark Stuberr on May 12, 2016 at 6:58am — No Comments
Building the 16 foot double ender with transom. Is solid lumber, say Sapele, a good idea for the transom, rather than plywood? Thanks
Added by Dave Curtis on May 7, 2016 at 10:58am — No Comments
If a sucker is born every minute, I must have been born more than once...
I picked this boat up over the weekend. It was rougher in person than I expected (hoped) from the pictures, but I liked the size and its history -- it was built 35 years ago to run the Grand to support a bunch of kayakers. I can't imagine taking it down there with no compartments and about 10 scuppers (covered now by the small pieces of wood on the gunwales) cut-in at floor level to encourage self bailing.…Continue
Enky continues to take shape on the drawing table. Check out the progress here.
Added by Mark Stuberr on April 11, 2016 at 6:47am — No Comments
Added by Mike Morris on March 24, 2016 at 8:15pm — No Comments